Installing and removing the oil filter is a hefty task if you are unaware of the proper ways. Many customers install the oil filters easily but find them difficult to remove at the time of the next filter replacement. If you are struggling to find out how to remove a stuck oil filter, you are in the right place. We have got you covered on this.

Before we look at removing the oil filter, let’s first see what a stuck oil filter looks like. Let’s get started!

What Is A Stuck Oil Filter?

There are two possibilities whenever anyone mentions that your vehicle’s oil filter is stuck. Either the oil filter has lost its outer covering, and the whole inner part is stuck in place, or the filter threads are blocked so they can’t be lost or tightened anymore because of being stuck. It can also happen if you use a bad or wrong oil filter for your car.

In both cases, the oil filter gets stuck badly and can’t be removed easily with bare hands; now, it becomes important to see how to remove a stuck oil filter.

Let’s have a look below!

How To Remove A Stuck Oil Filter?

Like any other stuck item, it is also difficult to remove the stuck oil filter. As we read above, the oil filter gets blocked in two ways, and in both ways, it is difficult to remove the oil filter with your hands.

To remove the stuck oil filter, there are a few ways:

Wrench

Although it is recommended not to use a wrench or any similar tool to install or remove an oil filter, removing a stuck oil filter is necessary. 

All you need to do is take a wrench, fit it exactly on the oil filter’s inner body if it is without the outer covering and rotate it anti-clockwise slowly without exerting much force on the filter. Some special oil filter wrenches are available in the market, and it is advisable to use them for this.

Sand Paper

Removing the stuck oil filter with a wrench is not always effective. If you have a rubber oil filter wrench, it might slip again. The better way is to use sandpaper. The sandpaper helps to make a better grip around the oil filter.

Sandpaper alone can’t remove the blocked oil filter. All you need to do is take the sandpaper, grip it around the oil filter tightly, and then use a wrench to remove it. The sandpaper will help make a strong grip around the oil filter and stop the wrench from slipping down.

Lubricating Fluid

When you change or replace the oil filter after a long time, it might be possible that it is stuck there badly, and the threads are stuck to the body of the block where the oil filter is installed. 

Now to remove the oil filter, you can take the help of a lubricating fluid or spray and spray it to the point where the stuck oil filter meets the block. This will make the oil filter lubricate; meanwhile, you can try removing it with your hands or using any wrench. 

Hammer and Screwdriver

Using a hammer and screwdriver to remove the stuck oil filter is the last good way which is why this should be removed in the worst case when you have tried all the above ways of removing an oil filter.

To remove the stuck oil filter using a hammer and screwdriver, you need to place the screwdriver at the point where both the oil filter and block meet, hammer on the screwdriver, and as soon as it gets a bit in, pull it off to remove the stripped oil filter completely. 

What To Keep In Mind While Removing A Stuck Oil Filter?

There are a few things that you should keep in mind while removing a stripped oil filter:

  1. Always be gentle and do not apply too much force in the first instance on the stripped oil filter as this may lead to crushing the oil filter, and it will get more difficult to take it off then.
  2. Never remove an oil filter just after turning off the engine. You may end up hurting your hands.
  3. Always keep an oil pan or something in your hand, as there might be a possibility of some oil trapped outside the oil filter’s gasket.
  4. Use a hammer and screwdriver to remove the stuck oil filter only in the worst cases, as pulling off the filter can also cause other unwanted damages.

Conclusion

A stuck oil filter is difficult to remove as either it is without an outer covering or the threads are blocked, so it becomes difficult to make a grip around the oil filter. To remove a stuck oil filter, you may try using the abovementioned methods.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *